| 释义 |
bending moment ˈbendiŋˈməumənt 短语⁹⁰⁸⁸⁷⁺⁷
基本例句
弯矩,弯曲力矩,挠矩,弯曲矩
The basic idea is as follows: the redundant bending moment is assumed at a virtual hinge at the middle support and calculated using compatibility condition of deformation.
基本思路：在中间支座设虚铰代之以冗力弯矩，并利用变形协调条件求出该值； cnki
The counterweight is installed on the crankshaft for reducing the bending moment on it, but it will influence the magnitude and distribution of the main bearing load.
曲轴上平衡重的安装减小了曲轴所受的弯矩，但也影响了主轴承载荷的大小和分布。 cnki
The influence degree of furniture material to breaking bending moment and rigid efficiency in bamboo glue- laminated panel is bigger than those in medium density fiberboard and particleboard orderly.
基材对接合点的破坏弯矩、刚性效率影响较大，两个性能指标的值由大到小依次为竹集成材、中密度纤维板和刨花板。 cnki
Considering vertical and horizontal bending moment and tortile moment action together, equivalent bending moment is proposed in this paper to evaluate anti- bend capability of wall.
基于墙体受到纵向弯矩、横向弯矩和扭矩的综合作用，提出采用等效弯矩法评价墙体的综合抗弯性能； cnki
Experimental results show that the total Vertical Bending Moment can be divided into one low frequent component due to wave loads and one high frequent component due to whipping loads.
试验数据分析表明，合成弯矩可以分成由波浪载荷引起的低频成分以及由砰击载荷引起的高频成分。 cnki
How to check the flange leakage problem due to bending moment?
如何去校核由于弯矩导致的法兰泄漏问题？ pipingsoft
In this paper, new method on calculation of absolute maximum bending moment and position is introduced, and use influence line to check and compare to tradition method.
本文介绍了用一种计算梁最不利荷载位置及绝对最大弯矩的新方法，并用影响线进行校核，同时与传统方法进行比较。 chemyq
In a simple supported beam the maximum bending moment occurs at the center, diminishing to zero at the ends.
在一座简支梁上最大弯矩是在中部产生，在两端减少为零。 svtcc
Increasing brace pre axial force can effectively control the wall displacement and reduce negative bending moment.
增大支撑预加轴力可以有效的控制连续墙的变形，减小墙身负弯矩。 cnki
Increasing brace stiffness will reduce the wall displacement and result in plus bending moment reducing, negative bending moment improving.
增大支撑刚度，可以减小墙身位移，引起连续墙正弯矩减小，负弯矩增大。 cnki
Motorcycle disk brake is widely used because of its small radial dimensions, axial application of force along the disk when braking, no bending moment on brake shaft and braking stability.
摩托车液压盘式制动器径向尺寸较小，制动时沿制动盘的轴向施力，制动轴不受弯矩，制动性能稳定，应用较广。 cnki
Negative bending moment nearby the middle supports of composite steel- concrete continuous beam bridge, will cause floor deck concrete to crack and shorten its life.
钢-混凝土组合连续梁桥的中间支座附近为负弯矩区，会导致桥面混凝土开裂，缩短使用寿命。 cnki
The maximum bending moment and shear force of concrete core mixing pile are greater than pile foundation's under the same seismic response.
在相同地震作用下，劲性搅拌桩单桩的最大弯矩和剪力均小于桩基础； cnki
The model is not competent in describing the boundary condition of the bending moment, but it is not a fatal drawback because fabric cannot generally stand the bending moment.
该方法存在不能描述弯矩边界条件的缺点，但对于织物悬垂模拟来说足够可行，因为织物一般不能承受弯矩载荷。 cnki
This paper analyses the relativity between bending moment M and axial force N in calculating ground supporting capacity, and the effect of relativity on reliability calculation.
分析了在地基承载力验算中，弯矩 M与轴力 N之间相关性的存在，以及相关性对可靠度计算的影响。 cnki
This paper studied the relationship among bending moment, curve, deflection and concrete compression height by design principle for reinforced concrete structure.
从钢筋混凝土结构设计原理出发，分析截面弯矩、曲率、挠度、受压区高度之间的相互关系； cnki
With the limitations of the maximal bearable bending moment and the positive lifting force, the controlling parameter curves of span and lifting angle are then acquired to guide the safety operation.
以长桩结构能够承受的最大弯矩和吊点力不为负值作为限制条件，得出安全作业跨距和倾角参数控制曲线。 cnki |