释义 |
PTFE高 基本例句 abbr.聚四氟乙烯=Polytetrafluoroethylene The “ bearings” will be formed by cylindrical PTFE pieces of6mm diameter that will have to be inserted into the inner side of the “ arms” of the “ Y” shaped bearing parts. 的“轴承”将成立圆柱聚四氟乙烯件6毫米直径将必须插入到内侧的“武器”的“ Y”型形轴承零件。 http://bbs.5imx.com The moulding technology of PTFE foam was described. 介绍了聚四氟乙烯 PTFE泡沫材料的成型工艺。 chemyq The roof membrane is PTFE, which is 50% transparent and provides natural daylight while protecting the fans below. 屋顶防水层是聚四氟乙烯 PTFE,其透明度为50%,在提供自然日光的同时,保护下面的球迷。 yeeyan The test data indicate that the PTFE film lamination fabric has fine heat insulating ability in cold. 测试数据表明, PTFE薄膜层压织物在寒冷大风的环境中具有优良的保暖性能。 cnki Engineering internal: for carbon black, graphite, glass fiber, PTFE packing material has good wetting role. 工程内部:对碳黑、石墨、玻璃纤维、 PTFE等填料有良好的润湿作用。 lifengsuye Expansion concept of PTFE dispersion resins and concerned parameters are introduced, and processing procedures, method and devices are reviewed in combination with examples. 介绍了聚四氟乙烯分散树脂膨体化的概念和有关参数,结合实例叙述了其加工工艺、方法和设备。 cnki For most specialty gases, CTFE is recommended over PTFE because it is less permeable to oxygen and moisture, and evidences less cold flow. 对于大多数特种气体,推荐使用 CTFE,而不是 PTFE,这是因为 CTFE对氧气和水蒸汽的渗透性更差,冷变形也较小。 www.airproducts.com.cn For PTFE seats multiply the numbers shown on this chart by2.0. 对于聚四氟乙烯阀座,请用2.0乘于表中的数据。 tdict If you must use a PTFE- lined pan, keep your stove’s burner on medium or lower. 非要使用 PTFE聚四氟乙烯内衬的平底锅时,应保证炉头处于中等或更低温度。 ebigear If you must use a PTFE- lined pan, keep your stove's burner on medium or lower. Also, never preheat an empty pan. 非要使用 PTFE聚四氟乙烯内衬的平底锅时,应保证炉头处于中等或更低温度。另外,绝对不要预热空无一物的平底锅。 ebigear Joint sealant gasket of expanded PTFE made of pure PTFE is a continuous low density cord. 膨胀聚四氟乙烯密封胶带是用聚四氟乙烯制成的低密度密封材料。 cnki Plastic products, have a good corrosion resistance, the more common use. Varieties are polyethylene, polypropylene, soft PVC, PTFE, nylon66, nylon, etc.1010. 塑料制品,有很好的耐腐蚀性能,使用也较普遍。品种有聚乙烯、聚丙烯、软聚氯乙烯、聚四氟乙烯、尼龙66、尼龙1010等。 blog.sina.com.cn Plunger extrusion molding mechanism of PTFE is introduced, process method and equipments for extrusion molding are also reviewed. 介绍了聚四氟乙烯悬浮树脂柱塞挤出成型的原理,叙述了挤出成型加工的工艺方法及设备。 http://dj.iciba.com Solid, fully isolated type 316 stainless steel stem is additionally PTFE coated as a safeguard. 实心、完全隔离的316不锈钢阀杆,附加 PTFE涂敷以增加安全保障。 h6688 The results show that the microstructure of nano- PTFE composite coatings is obviously fined. 研究结果表明:纳米 PTFE的加入明显细化复合镀层。 cnki The results indicate that, of three combinations, the PTFE- granite couple has the smallest difference, only0.02, between the kinetic and the static coefficient. 试验结果表明, PTFE—花岗石的动、静摩擦系数之差是三种摩擦副中最低的,仅为0.02。 cnki This is especially important when PTFE washers are being used in acid gas service where the elimination of moisture contamination is critical. 当 PTFE垫圈用于去除水蒸汽污染十分关键的酸性气体设施时,这是特别重要的。 www.airproducts.com.cn When PTFE washers are used in systems using water- reactive acidic or basic gases, their moisture can cause the formation of corrosive acids or alkaline liquids in the system. 当 PTFE用于使用可以同水反应的酸性或碱性气体气体的系统时,它们的水蒸汽会在系统内导致腐蚀性酸性或碱性液体的生成。 www.airproducts.com.cn PTFE is compatible with most gases and is the most common washer material used with specialty gases. PTFE同大多数气体相容,是用于特种气体的最常用的垫圈材料。 www.airproducts.com.cn PTFE is also permeable to moisture and oxygen, which can cause micro contamination in sensitive processes. PTFE还能透过水蒸汽和氧气,在敏感过程中这会导致微小污染。 www.airproducts.com.cn |