| 释义 |
molding machine短语¹⁴⁴⁹⁷²⁺²
基本例句
模塑成形机,造型机,制模机
The paper has discussed the hardware structure and software designing of the single chip computer control system for Discal Graduator Paper Cup Molding Machine.
介绍了采用单片微机对圆盘分度式纸杯成型机进行控制的系统硬件结构及其软件设计思路。 d.wanfangdata.com.cn
The reciprocating screw injection molding machine is considered as consisting of two halves: a fixed injection side, and a movable clamp side.
往复螺旋注塑成型机被认为由两部分组成：一个固定注塑端和一个活动夹具端。 mapeng
The working principle and main components of control system of inducing fully electrical injection molding machine were presented.
介绍了诱导式全电动注塑机电控系统的工作原理和主要组成部分。 cnki
Company imported advanced Krupp Blow Molding Machine from Germany, so that the quality of products are fully guaranteed.
公司引进先进的德国克虏伯中空吹塑机，使产品质量得到充分的保证。 iciba
If the selection of materials, Selection of injection molding machine, Parts structure analysis and design of mould parts, Calculation of water cooling system, Design of cavity and formwork, etc.
如对材质的选择；注塑机的选择；零件结构分析，并对模具零件进行设计；对冷却系统水管计算；对型腔和模架设计等等。 blog.sina.com.cn
Injection molding machine plays an important role in plastic industry, as the main equipment and typical representation of injection molding mechanism.
注塑机是注射成型的主要设备，它是塑料加工机械的典型代表，在塑料工业中有其特殊的地位。 cnki
Injection molding machine working condition should hang“ state” brand.
注塑机的工作状态需挂“状态牌”。 lifengsuye
The paper describes the development and application of close-loop control system for hydraulic injection molding machine.
本文阐述了油压注塑机闭环控制系统的开发与应用。 chemyq
The design, molding techniques, special injection molding machine and computer assistance analysis of the alkaline storage battery plastic shell were discussed.
从制品设计、模具设计、成型工艺、专用注塑机、计算机辅助分析等方面对碱性蓄电池塑料壳进行了研究。 cnki
The electricity consumption of oil pump of hydraulic pressure system accounts for80% of that of the whole plastic injection molding machine, so it is crucial to lower the electricity consumption.
其中液压油泵的用电量占整个注塑机用电量的80%以上，所以降低其耗电量是注塑机节能的关键。 com
This paper introduces the design and implementation of parison wall thickness control system in blow molding machine.
介绍了型坯壁厚控制系统在中空吹塑机中的设计与实现。 cnki
This paper introduces domestic, foreign development and research on clamp unit in injection molding machine and heat transfer technology, and their advantages and disadvantages are discussed further.
本文介绍了国内外注塑成型机合模机构和强化传热技术的研究发展及现状，并分别讨论了它们的优缺点。 dictall
Two kinds of injection systems of full electric injection molding machine are analyzed.
分析了全电动注塑机的两种射胶系统。 chemyq
Working status of a micro jolt molding machine in stroke of air inlet and expansion has been tested by method of acceleration to find out the proper range of such stroke of an optimal working.
采用加速度测定法测出气动微震造型机在不同进气行程与膨胀行程下的工作状况，从而找出其最佳工作状况下的进气行程与膨胀行程的合理范围。 chemyq
Molding machine is controlled by PLC linkage procedure. It can run long and stably just need one time adjust.
成型机采用 PLC程序联动控制，只需一次性调节得当，长期使用联动程序性能稳定。 shguqiao |