| 释义 |
applied load短语¹⁴⁴⁹⁷²⁺²
基本例句
施加负荷,外加负载,外施荷载,使用负荷,外施载荷
The deformation remaining after an applied load is removed is called plastic deformation.
这种载荷卸除后仍然存在的变形，称为塑性变形。 http://jpkc.svtcc.net
The linearity between the electrical resistance change and the applied load was good for the carbon fiber reinforced cement based material.
碳纤维水泥基材料的电阻变化与所受荷载呈良好的线形关系； cnki
As the product structure, external applied load and service conditions difference, makes the test result to be widely divergent and resulting in the result does not have a generic.
由于产品结构、外载荷和使用环境的差异，使得试验结果大相径庭，从而导致结果不具有通用性。 fabiao
Because the hardness number obtained depends on the applied load, Knoop test restless should always cite the load used.
因为硬度值的获得和载荷十分密切，所以不太精确的努氏试验总是采用用过的载荷值。 blog.sina.com.cn
Chip behaviors were analyzed using scanning electron microscope SEM, to study the effects of applied load, scan cycles and scanning direction on nanomachining of Al and Cu samples.
切屑形态通过扫描电子显微镜 SEM进行观察，分析了不同垂直载荷、循环次数和针尖加工方向下铝铜被加工表面的切屑形成过程。 dictall
Creep is defined as the gradual extension of a material under a constant applied load.
蠕变是指材料在不变的载荷作用下逐渐伸长的现象。 choicebest
Elastic deformation is nonpermanent, which means that when the applied load is released, the piece returns to its original shape.
弹性形变是非永久性的，即撤去加载后，样品可恢复初始的形状。 dmse.jlu.edu.cn
Elastic recovery means that when the applied load is released, the piece returns to its original shape.
弹性回复是指当样品所受应力撤销后，其完全回复到初始形状的现象。 dmse.jlu.edu.cn
Plastic deformation independent of the time duration of the applied load is known as slip. Creep is plastic deformation that continues to increase under a constant stress.
与加载持续时间无关的塑性变形，称为滑移。蠕变徐变是在恒定应力下继续增长的塑性变形。 http://jpkc.svtcc.net
Plastic deformation takes place first at the crack tip and spreads across the solid as the applied load is increased beyond general yielding.
塑性变形首先发现在裂纹顶端，当工作载荷超过了普通屈服时，则传播到物体中。 bab
Stability state is considered only relating to self weight in current stability analysis of underground cavity, while the applied load is neglected, so its conclusion is over safe in general.
以前的地下洞室围岩稳定性分析，一般仅考虑在自重作用下的稳定性状态，而忽略了地应力对围岩稳定性的影响，所得结论往往偏于保守。 cnki
The result shows that the optimal value of filler metal thickness exists and the residual stress decreases with the applied load increasing.
结果表明，钎缝厚度存在最佳值，在一定范围内钎焊压力增大，残余应力减小。 cnki
This is the temperature at which a simply supported beam specimen of the material, with a centrally applied load, reaches a predefined deflection.
这是中心承载的该材料简支梁达到预定偏差的温度。 mapeng
With increasing the applied load and sliding velocity, the friction coefficients decrease.
随着载荷和摩擦速度的增加，摩擦系数减小。 cnki |