| 释义 |
flanging 英'flændʒiŋ美'flændʒiŋ BNC²³⁶²¹³⁺¹
基本例句
n.作凸缘²⁰折边;镶边⁴⁰;外缘翻边²⁰;翻口²⁰
In addition, using columniform punch and conical punch, different stress- strain distribution and thickness distribution at deformation region of flanging is compared.
通过采用不同凸模型式，比较了柱形凸模和锥形凸模翻边时变形区的应力应变及厚度分布的不同。 iciba
The application of the rotational graded wedge mechanism in a flanging die for the shell plate metal sheets greatly raises the production efficiency.
将双向运动斜楔与旋转斜楔进行了对比，在侧围板外覆盖件翻边模具中采用旋转斜楔成形机构，大大提高了生产效率。 chemyq
The joint of perpendicular flanging insert and slanting flanging insert was one of the difficulties in automobile panel die design.
垂直翻边凹模镶块和倾斜翻边凹模镶块的交接是汽车覆盖件模具设计的难点之一。 dictall
The characteristics of the corner rain eaves parts and their forming principle were analyzed. The compound forming was broken into simple bending and flanging.
分析了角部雨檐零件特点及其成形机理，将复合成形分解为简单的弯曲和翻边。 cnki
The forming technology of rear shock absorber cap is analyzed, and its drawing die, flanging die and spinning die structure are also introduced.
分析了后减震器帽的成形工艺，介绍了成形该零件的拉深模、翻边模以及旋压模具结构。 zidian8
The influence of average normal anisotropic coefficient on the flanging height can be considered in this model.
该模型考虑厚向平均各向异性系数对翻边高度的影响。 ilib
The stamping process includes punching, bending, irregular flanging, bulging, partial embossing and re striking, etc.
冲压工艺有冲裁、弯曲、不规则翻边、胀形、局部压凸、整形等。 cnki
The structure feature, working principle and design point of compound die including blanking, drawing, punching and flanging are also introduced.
介绍了落料—拉深—冲孔—翻边复合模结构特点，工作原理及设计要点。 cnki
A device which can fulfill punching, flanging and thickening in one stroke of press machine is studied.
研制了可在压力机一次行程中实现冲孔、翻边和增厚边缘的装置。 chemyq
As a less using cylinder flanging die, it is designed using a sliding punch to flange.
针对以往较少出现的筒形件垂直翻边模，设计出了一种利用可滑动的凸模对其翻边。 chemyq
Based on the inverse approach, the trimming line and the formability of the sheet metal at local flanging area can be predicted from the geometry of the designed part.
该系统基于有限元逆算法，根据翻边形状反向快速计算修边线尺寸以及翻边成形中可能出现的起皱和破裂等缺陷。 dictall
Based on the above and combination with a practical example, this paper presents a calculative method for flanging force.
在此基础上，结合实际算例，提出一种翻边力的计算方法。 chemyq
In addition, according to experimental results, slab method in plastic mechanics and material hardening theory, a new formula for hole flanging force is concluded.
另外，根据试验结果，并利用塑性力学中的主应力法和材料硬化理论，推导了一个计算圆孔翻边力的新公式。 cnki
Manufacturing the automobile spoke components is a multi- step stamping forming process, the round- hole flanging often cracks in the last process.
汽车轮辐零件的制作是一个多工步冲压成形过程，在最后一道工序圆孔翻边时经常出现开裂。 hbfsdy
Plasticity in the suppression techniques such as stamping, bending, flanging, such as tensile plate.
适用于可塑性的压制工艺，如冲压、弯曲、翻边、薄板拉伸等。 iciba
Reasonable die structure dimension and optimum time of flanging and discharging were determined through theoretical analysis.
并且通过理论分析，确定了水平翻边和局部弹性退料的合理尺寸以及最佳时机。 chemyq
Taking the front floor as an example, mainly introduced the hoisting wedge driver installed in active pressing material core and making use of reverse wedge driver to form the up flanging structure.
以某车型前地板为例，重点介绍了吊装斜楔驱动器安装在活动压料芯上的结构和利用反向斜楔完成向上翻边的结构。 dictall
The system uses associated design idea in order to realize input of flanging die model parameter and harmonious unification of structure redesign.
采用关联设计思想，实现翻边模模型参数的输入与结构再设计的和谐统一。 chemyq
The deep drawing, trimming and flanging is the most basic three processes.
而拉深、切边和翻边是最基本的三道工序。 fabiao
The method is suitable for calculation of blank of fillet corner flange of motor vehicle odd shaped parts and no trimming operation is necessary after flanging process.
该方法适合汽车异形件的角部翻边毛坯计算，翻边后无需修边处理。 cnki
The ultimate hole- flanging coefficient is given in two different states, while the non axisymmetric distortions are quantitatively described and analyzed.
本文在给出极限翻边系数结论的同时，对非轴对称畸变现象进行了定量描述、分析与解释。 cnki |