| 释义 |
cover plate短语³⁸¹¹⁰
基本英英例句例句
电机活动盖板; 盖片; 盖板,荧光屏前面防护玻璃
Noun:
covering consisting of a plate used to cover over or close in a chamber or receptacleThe injection mould for a duplicatorcover plateis designed.设计了复印机盖板的注塑模具。
Remove thecover plateof the relief valve by removing the four connecting screws.通过拆卸四个连接螺丝来拆卸安全阀盖板。 In addition, to obtain the perfect structure of ceramic cover plate, the stress distributions in different shape, dimension and boundary conditions are calculated.
为了得到符合工作要求的较为理想的陶瓷盖板结构形式，研究了盖板形状、尺寸大小、支承条件对应力分布的影响。 cnki
Parts and components products include: chassis, cover plate, stamped steel, brush components, electrophoresis rotor, etc.
零部件产品有：机壳、盖板、冲片、电刷组件、电泳转子等。 jingxida
The prestress of steel girder by high strength cover plate can raise stiffness and save steel, with simple configuration.
焊接高强钢盖板的预应力钢梁构造简单，刚度较大，节约钢材，是一种值得推广的结构型式。 cnki
The viscoelastic damping material is located between high-low cover plate mainly provide damping for bearing, to absorb earthquake energy;
粘弹性阻尼材料夹于上下盖板之间为支座提供阻尼，达到消能减震的效果； dictall
An injection mould with open-type cavity and slide block type of ejection mechanism was developed after an analysis on the forming process of a slicing insulating cover plate.
通过对限幅绝缘盖板的工艺分析，确定了开放型腔、滑块脱模的模具结构。 dictall
Cable inlet for bottom elevated cover plate:the cover plate can be dismounted to drill holes and the seal rings are provided.
底部凸台盖板进线，盖板可预先拆下开孔，并配有密封圈。 eleweb
Drill& tap for M16X2-1.38 Deep NPT,16 places for cover plate mounting screw.
钻孔，攻出一只 M16X2-1.38深 NPT螺纹，16处，该螺纹应与盖板固定螺丝配套。 dictall
Each check module shall have a captured spring and be accessible through a bolted cover plate.
每个止回模块应该配置一个复位弹簧，并且易于从螺栓阀盖板处接触检测或维修。 h6688
Escalator products are not including: balustrades, lighting fixture, skirtings, inside and outside cover plate and entrance treadcleanness.
对于扶梯产品不包括扶梯扶手及照明灯具、裙板、内外盖板和扶梯入口踏板的清洁。 tianya
If need to put a word in bed cover on the first go to bed cover and the tools and turning on a bed cover plate.
如需要放的话般先在床面上盖上床盖板，把工具和车刀放在床盖板上。 hfwhjx
In order to overcome the difficulty of heavy cover plate installation with two times of welding, a welding procedure finished cover plate welding at one time is put forward.
针对采用“两次拼焊工艺”拼焊大型盖板存在的问题，提出了“一次拼焊”工艺。 cnki
Outdoor cable trench are reinforced concrete trench with reinforced concrete cover plate.
室外电缆沟由钢筋混凝土砌成，上面加钢筋混凝土盖板。 www.1x1y.com.cn
Remove all nuts and bolts from cover plate and take off plate.
从盖板上拆卸所有螺母和螺栓，然后将盖板拿开。 h6688
Specific measures and suggestions for the repair of fatigue cracks on the upper cover plate are also put forward, which is significant for safe production.
给出了上盖板疲劳裂纹的具体修复措施和建议，对于安全生产具有重要意义。 airiti.com
Study on culvert energy-dissipating cover plate in dispersive delivery system is performed.
就分散输水系统中廊道支孔设置盖板这一共性问题，作了较为系统的研究。 cnki
The injection mould for a duplicator cover plate is designed.
设计了复印机盖板的注塑模具。 chemyq
The tank shall be internally protected in such manner that no rust falls down to the surface of cover plate to cause electro-chemical corrosion;
对油罐内壁应做防腐处理，防止大量铁锈碎屑落到盖板上产生电化学腐蚀； cnki
This article puts forward to lay a cover plate in the welding of the titanium sandwich pressure vessel and it also presents the structure and welding practice of the cover plate.
文章提出了在钛复合板压力容器的焊接中采用盖板敷设焊接，并具体介绍了盖板的结构及其焊接方法。 dictall
To release bladder from opposite end, remove all nuts from flange and then take off cover plate.
为了将内胆从另一边分离开来，就要从法兰上拆卸所有螺母，然后拿走盖板。 h6688 |