| 释义 |
cog·ging 英'kɒgɪŋ美'kɒgɪŋ COCA²⁵⁴³³⁷⁺⁶
基本英英搭配记法例句例句
n.齿轮⁵⁰初轧;打榫⁵⁰
名词 cog:
a subordinate who performs an important but routine functiontooth on the rim of gear wheelcogging mill初轧机,开坯机,粗轧…cogging effect嵌齿效应cogging down pass开坯孔型cogging pass开抛型cogging down开坯cogging roll开坯轧辊,粗轧辊…cogging shears初轧坯剪切机…cogging joint齿节,榫齿接合…cogging hammer开坯锻锤cogging down roll开坯机轧辊cogging-down roll开坯机轧辊cogging engine开坯原动机
cog-ging⇒n.齿轮⁵⁰初轧;打榫⁵⁰
名词100%
Firstly, using finite element analysis to describe that cogging force was the main cause of force ripple in tubular permanent magnet linear motors.
首先用有限元分析来说明该文所研究的圆筒永磁直线电机推力波动主要是由齿槽力引起的。 china-micromotor
The multi-pass cogging of H-beam was simulated by finite element method with commercial software ABAQUS.
运用商业有限元软件 ABAQUS模拟热轧 H型钢的开坯过程。 cnki
The calculation formula of the cogging torque are derived by the Fourier decomposition and the virtual displacement method.
利用傅里叶分解及能量虚位移法，推导了磁阻转矩的计算公式。 cnki
Two methods of reducing cogging torque, namely, the stator tooth notching and the two rotor pole stacks shifting are presented.
介绍了定子齿面加辅助凹槽和转子磁极分段移位两种抑制磁阻转矩的方法。 dictall
Based on three dimensional finite element analyses of magnetic fields, the cogging torque of a prototype motor is calculated using the virtual work and Maxwell stress tensor methods.
在电机内磁场三维有限元数值分析的基础上，采用虚位移和麦克斯韦张量两种不同的方法计算了电机的脉动转矩。 cnki
Because of the differences on structure and operational principle, the ways of reducing cogging torque in DSPM is different from other permanent magnet motor.
与其他永磁电机相比，由于结构和运行原理的不同，双凸极永磁电机齿槽转矩的削弱方法也有所不同。 www.micromotor.com.cn
By electromagnetic field finite element simulation, the influence of cogging structure and pole width on the BEMF waveform was pointed out.
通过电磁场有限元仿真，指出电机齿槽结构和磁极宽度对反电势波形的影响。 china-micromotor
Factors influencing noise of the motor systems such as cogging torque, HALL signal errors and armature magnetic field are analyzed.
本文分析了影响永磁同步电机噪声的因素，如定位力矩，霍尔信号的误差以及电枢反应磁场等。 dictall
In this paper, the main factor— cogging effect that cause torque ripple is simulated and analyzed.
对引起转矩脉动的主要因素——齿槽效应，进行了仿真分析。 dictall
Moreover, the force ripple arose by end effect and cogging effect also exists in system.
此外，还存在因边端效应、齿槽效应等引起的推力波动。 physics.zju.edu.cn
On this basis, back electromotive force without load and with load is researched, simulated and analyzed, and cogging torque is analyzed and calculated in different dimensions of magnetic steel.
在此基础上，仿真了空载和负载下的电机反电动势，并且对不同磁钢尺寸下的定位力矩进行了分析计算。 dictall
One immediate benefit of having“ air coils” is obviously the complete lack of cogging, which, if used in a windmill should result in a machine that starts very easily.
一个直接的好处有“空气弹簧”显然是完全没有脉动，而如果使用风车应导致机器，开始变得非常容易。 tech-domain
Results show that cogging using concave anvil can increase the deformation at the center part of the billet and can press holes more effectively.
实验结果表明，利用凹面砧拔长，锻件心部能够获得更大的变形量，对空洞的压合效果更好。 cnki
Since the LSR to be detected with cogging structure, which makes the gap sensor's output with cogging effect.
由于被检测体长定子轨道具有齿槽结构，使得传感器的输出具有齿槽效应。 fabiao
Step skewing of rotor magnets is an efficient manner for reducing harmonics and minimizing cogging torque and torque ripple.
转子分段斜极是一种能有效削弱齿谐波、改善电机齿槽转矩和转矩脉动的方法。 airiti.com
The first stage is called primary rolling, or cogging.
这个阶段叫作初轧或开坯。 tdict
Theoretical analysis shows fractional slot winding can effectively reduce the end of windings and cogging torque.
理论分析表明分数槽绕组能够有效减小电机定位转矩与转矩脉动，减小绕组端部长度。 china-micromotor
To minimize the cogging torque, a global optimization algorithmzooming algorithm and the finite element methodFEM are combined to find the best pole arc combination.
为使齿槽转矩最小，采用全局优化方法与有限元相结合以获得最优极弧系数组合。 cnki
When cogging effect too big will affect the suspension control of HSMV, thus affecting the normal operation of HSMV.
当齿槽效应比较大时会影响磁浮列车的悬浮控制，从而影响磁浮车的正常运行。 fabiao
Cogging is a problem in permanent magnet alternators, especially for wind generators.
齿槽是一个问题永磁交流发电机，特别是对风力发电机。 tech-domain
Cogging torque is one of the main concerns of permanent magnet motor.
齿槽转矩的削弱一直是永磁电动机研究的重点之一。 dictall
The accurate calculation of cogging torque assists in optimizing the design of claw pole permanent magnet synchronous motors.
脉动转矩的准确计算是爪极永磁同步电动机优化设计的基本前提之一。 cnki |